Size Genetics Extender Modification instead of using the strap ?

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

Hello,

Is there a comfortable modification like a vacuum cap modification that will work with the size genetics extender ?

The thing I don't like is that it slips out of the strap too often sometimes. So then I strap a little tighter and I worry about blood flow. This starts to become a bit of a hassle.

I do tape first, but the tape seems to slip a bit against the skin, causing the strap to slip as well.

I also put on the foam ring, but that does nothing much to help. I guess it adds the slightest amount of comfort.

I am thinking there is a vacuum hanger attachment that can be added to this extender ?

Other ideas ?

[not2big Senior Super ModeratorPEGym Hero Find all posts View Profile Close not2big]

You should check out the VacExtender mod kit. It fits on the SizeGenetics.

[Muffbuster Junior Member Find all posts View Profile Close Muffbuster]

If you have a phallosan you can use the bell from that also.

[BobbyR_SG_Rep Official Size Genetics Representative Find all posts View Profile Close BobbyR_SG_Rep]

How long are you able to extend until your penis pulls out? Might you be using too many rod lengths during your training?

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

How long are you able to extend until your penis pulls out? Might you be using too many rod lengths during your training?

It varies how long. Sometimes everything goes for hours before it pulls out. Not sure it is the rod lengths but how far I twist the things near the base to get extension.

I could be extending too far, but I wanted more stretch than say an ADS. I could back off on the stretch and probably would last longer before pulling out at times. I could also strap the thing a bit tighter, that kinda makes me nervous too strap too tight.

[BobbyR_SG_Rep Official Size Genetics Representative Find all posts View Profile Close BobbyR_SG_Rep]

Do you have any extra padding from your device kit to help prevent your penis from slipping?

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

Do you have any extra padding from your device kit to help prevent your penis from slipping?

No just the foam rings. I bought a piece of harder type foam used to cover pipes at the hardware store. I cut like a half piece and used that a few times.

Not sure that helped a lot. My idea was to be able to strap tighter as that would provide more protection. Still have to clamp down with that on, it just is softer than the strap.

Still with the penis being pulled back towards the body, over time that piece still slides a bit too if I don't clamp tight along with a good stretch.

[BobbyR_SG_Rep Official Size Genetics Representative Find all posts View Profile Close BobbyR_SG_Rep]

How about using something like rubber or silicone for extra padding?

[blacksun19 Junior Member Find all posts View Profile Close blacksun19]

If you can buy more matallic extends you could use ESL40 silicon cup too.

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

If you can buy more matallic extends you could use ESL40 silicon cup too.

How would that cup attach to the extender ?

[blacksun19 Junior Member Find all posts View Profile Close blacksun19]

You use the plastic part that you will attach the penis head on. It has a couple holes so you can actually attach (using this knot https://encrypted-tbn0.gstatic.com/i...gzhJb0pjOw_Vpd) the silicon cup on that. You will need to make your extender 2-3 inches longer because of the cup so you will probably make the device too long to be practical if you're in the range of length that I am (8"+) and you will need more metallic extenders as I said. This will look similar to that: http://phalloboards.websitetoolbox.c...photos-6791409.

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

You use the plastic part that you will attach the penis head on. It has a couple holes so you can actually attach (using this knot https://encrypted-tbn0.gstatic.com/i...gzhJb0pjOw_Vpd) the silicon cup on that. You will need to make your extender 2-3 inches longer because of the cup so you will probably make the device too long to be practical if you're in the range of length that I am (8"+) and you will need more metallic extenders as I said. This will look similar to that: Using the ESL40.com Silicone Cup with my Penimaster Pro Photos!!!! - PhalloBoards (Version 2.0).

That is interesting. I think I will try something like that.

Thanks!

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

You use the plastic part that you will attach the penis head on. It has a couple holes so you can actually attach (using this knot https://encrypted-tbn0.gstatic.com/i...gzhJb0pjOw_Vpd) the silicon cup on that.

What is this knot called ?

I am not too familiar with how to do that knot. Does that type knot attach to the ESL cup ?

If so I see 3 potential places to attach on the ESL cup plastic tip part.

1. 2 holes- these are very small on mine and no shoe lace could fit through them.
2. A slot in the middle that is closed so to speak.
3. 2 outer slots that are open at the bottom.

Which is best to attach through and how exactly ?

I am thinking maybe a thin shoelace and just hook around the 2 outer open slots or through the middle slot. Then go through the 2 holes on the sizegentics extender plastic tip part and tie a knot to secure it ?

[TheHolyGrail Member Find all posts View Profile Close TheHolyGrail]

I put the ESL cup on the sizegentics extender. The cup is really comfortable. Much more comfortable than the strap. It doesn't come off as easy to urinate. I don't think it is practible to wear outside of the house because of the extra length needed for the ESL cup.


Putting the ESL cup on an extender:

Pros:

Comfort

Cons:

Need more extension rods because of extra length needed for the cup

I don't think practical to wear outside of the house because of length

putting it on with the extender is more difficult for me