Square dick 7x7...good idea?

[CLOSEDDennyA Senior Member Find all posts View Profile Close CLOSEDDennyA]

Just an update guys. Sure this thread made sense to me when i wrote it but only a short time later and already i know why no one has a 7x7 dick. It wont fit! Not in my gf anyway. At 6beg she now struggles to fit my base in until after about 5 min of sex (and over 15min of foreplay before that) and teeth are scrapping at 5.6 meg (she can't deepthroat so no beg problems yet).

Academic discussion only but not of any use to me anyway practically.

Yeah it is very tough to fit I am sure and even more so if the girth is uniform to the tip. I am almost too much right now and would never want 7 in girth...totally honest

[Jay1983 Senior MemberMember of the Month Apr 2014, Sept 2016 Find all posts View Profile Close Jay1983]

I'm shooting for a 6x9.

[GoingForGold Senior Member Find all posts View Profile Close GoingForGold]

My base is 7"+ and it's awesome when I get it in. I'd be fine with 7"MEG but wouldn't want 7"x7"

[wannahung Senior Member Find all posts View Profile Close wannahung]

I'm shooting for a 6x9.

you'll have to resort to farm animals

[RodSteel69 Member Find all posts View Profile Close RodSteel69]

Yeahh man 7x7 is not common at all. If your gf is struggling with you now their is no point dude

[wannahung Senior Member Find all posts View Profile Close wannahung]

If your gf is struggling with you now their is no point dude

new GF??? Hell, ya need a GF and a huge canon

[wish-4-8 Senior Member Find all posts View Profile Close wish-4-8]

Anything past 6" in girth will create problems. If you want to get an idea of what 7 X 7 looks like, get some card stock, a ruler, scissors, and some tape and make a "penis model" out of it by cutting it up and rolling it into a tube. For kicks, try putting your mouth around it. Ouch! You probably would not be able to close your hand around it.

If that is too much work, go shopping for cucumbers. Find a thick one. Most are above 6" in girth. Cut one to 7" in length and there you have it. Now ask yourself, "Do you really want that?".

[MySword Senior Member Find all posts View Profile Close MySword]

My base is 7"+ and it's awesome when I get it in. I'd be fine with 7"MEG but wouldn't want 7"x7"

Yes but you are far longer than me (7bpel) so i think it is much more in proportion. that and my gf will not fit 7 meg comfortably if at all based on my experience so it is not a great combo in my case. your dick is one of the most impressive on here for size and proportion but then again you are far more dedicated than I...

[MySword Senior Member Find all posts View Profile Close MySword]

Were you exposed to hot rodding or engines at some point? I have only heard the term "Square" used in describing a bore and stroke combination of an engine i.e. a square bore and stroke of 7x7. I think there are a fair bit of women out there that could happily adapt to a 7" girth and just as many that wood run the other way. Pun intended

Yes square engines are good. But I atcually prefer undersquare for torque down low but that is another discussion (and sadly my dick is oversquare anyway).

I don't doubt some girls could take 7 but it would take years and years for my gf to take it (according to her and my experience) and even then she would much prefer 6 at most. When i work hard on foreplay and after 15 min of slowly built up fucking she gets so wet sometimes i think hmmm, maybe she can take more girth but i have two problems. One it still takes ages before she can take it (and i will never get head again...her mouth is tiny) and two i really need more length first. 7bpel is not nearly long enough if it get my goal of 6meg imo....out of proportion.

[MySword Senior Member Find all posts View Profile Close MySword]

Yeah it is very tough to fit I am sure and even more so if the girth is uniform to the tip. I am almost too much right now and would never want 7 in girth...totally honest

Yes i told her i wish my dick was 6 all the way up and she said that would make things 'tight' in her words. She said maybe meg if the head doesn't get much bigger but it will still take alot of work to get it in. My aim remains 8x6 (will take 7.5 x 5.8 or so though...) because if it get 6meg i think 8 will make a better looking dick and will allow me to hit the deep spots properly... Oral may be bad though because at 5.6-5.7 meg she is really struggling....teeth scraping...