Announcement

Collapse
No announcement yet.

Jockinthebox's Guide to Steel Cock Ring Selection

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • The original information on Jockinthebox's "Extended Wear Cock Ring CHALLENGE for / Girth / Length/ Gains" has been lost, so I did some digging to share this:

    jockinthebox - 05-09-2015

    Earlier this week, I decided to see what gains (if any) I could achieve by wearing my 1/2" X 2.25" surgical steel cock ring for a virtual non-stop 4-5 week period (1 month). Since I discovered I tend to maintain a more engorged, longer-lasting flaccid after PE when edging with my cock ring than without it; my theory is I might gain more / faster by wearing one for an extended time and maintaining that extra fullness/ blood engorgement.

    Some facts about the Cock Ring I'm wearing:
    It is the type worn beneath my balls and over the top of my dick (You can see a pic of it on me in my photo album or 2 pics on the cock ring group site if you're a member). Sizing is key, as this is a non-constrictive type steel ring. NEVER wear constrictive rings longer than 20-30 minutes to avoid severe injury ! This experiment may not work for guys who are "growers", since your flaccid needs to remain large enough 24 hours a day, in order for the ring to not fall off (which could get very embarrassing if it were to hit the floor and go rolling across the room or down the sidewalk)! I'm a "shower" and have worn mine all day and while asleep numerous times, never losing it. While my ring is somewhat snug, it can still be rotated completely around my flaccid package and does not restrict normal blood flow, except during an erection- while edging or during sex. Even then, it just retains the blood and fullness for a longer period of time, and is actually very enjoyable, never painful. I can ejaculate with it on without any pain or discomfort (I just shoot further!). Restrictive type cock rings that fit around the base of my shaft leave me with a feeling of incomplete ejaculation, which I find uncomfortable and sometimes painful. All this ^^^ is provided to give anyone wanting to try this experiment some info on the cock ring type /sizing necessary to remain safe.

    Basic schedule:


    1) I'll continue my regular PE routine, with the same frequency, reps & intensity (I am on a 2 on/1 off schedule).

    2) I've taken precise measurements, so the final measurements should revel if extended wear of this type cock ring has any effect on girth and/or length. Current/beginning measurements: BPSFL 7.125";FLBG 5.125"; FLMG 4.875"; NBPFL 5.875"; MEG 5.25"; BPEL 6.625

    3) I will only remove my cock ring when showering / manscaping and during my PE routine, but will wear it while sleeping, edging/ masturbating and sex (essentially 21-22 HRS/DAY). Btw, I edge daily, except rest days, usually between 30min. to an hour, but only ejaculate 3X/week or every other session.

    4) Barring any interruptions or delays, I expect to report my measurements / findings on or about June 10, 2015.



    jockinthebox - 05-16-2015
    OK, here's my 1st week update...EXTENDED WEAR COCK RING CHALLENGE

    I REALLY think this may be working! My flaccid hang has been significantly better, with slight engorgement of blood (even with NO arousal or semi-erection), During sex and edging, I'm 110%+ erect as might be expected with a cock ring, but the interesting difference is I am able to plateau and maintain much more easily and DO/ MMO virtually indefinately during sex/edging with this extended wearing of my cock ring, so far. Waking up with rock-hard boners EVERY MORNING this week (unusual for me 7 days ina row). My only issue has been some slight irritation on the top of my shaft right at the pubic bone, which I have been treating (successfully) with cocoa butter a couple of times a day (after shower/sex/edging & PE). Since this is a month-long experiment, I have ordered a different style of cock ring that (I hope) will be here in about a week. It's a steel "horseshoe" or "bull ring" type that has a gap between two balls. Like the Hardwear Horseshoe ring design, but without the curvy indentation. Mine's just round, but can be worn upside down to keep the engorgement without going over the top of my cock shaft, eliminating that irritation, I think. Will take a pic and add to my journal once it arrives. Haven't measured any and don't intend to until the month's over, but so far, I'm excited at how well this seems to be going. Much hornier than usual too...GF loves this project!! SO DO I!!!
    incogneeetoe
    Moderator
    Member of the Month Sept 2017
    *Special Appreciated Moderator Nov. 2021*
    PEGym Hero
    Last edited by incogneeetoe; 02-21-2022, 08:18 PM.
    03/2015 Start <Able to last ~ 2 mins PIV>
    Thread
    12/2019 EL: +2.2 MEG: +1 <Able to last 60+ mins PIV>

    Comment


    • I have always been interested in this "Challenge", and I struggled to find a properly fitting cock ring to try it out. I was in North America last month and I found a decent steel bracelet that does the trick, so I wanted to give it a go.

      I was especially eager to try it having read his results. I used to refer back to it periodically, but the initial posts in the Cock-Ring Challenge Group are now lost, it seems. I used the waybackmachine to find some of it (as posted above) but I could not get a capture of the results.

      03/2015 Start <Able to last ~ 2 mins PIV>
      Thread
      12/2019 EL: +2.2 MEG: +1 <Able to last 60+ mins PIV>

      Comment


      • I tried this before and didn't work because the horseshoe ring hurt putting it on, like it was crushing my penis.
        I measured again just now, with a thin, narrow measuring tape (just a hair over a 1/4" wide).
        • Tight I got 7.5" circumference which is 2.388 diameter/60.6mm.
        • Very tight it was 7" circumference which is 2.229 in diameter/56.6mm
        One piece rings scare me because of the idea of getting stuck and having to cut them off.

        An idea I have is to get a length of sculpting wire, the thicker one, and perhaps solder it to those measurements as a ring, then try it on and see. Beats ordering different sizes and having to pay shipping for returns or not being allowed a return. And if it suddenly gets too tight it's easily cut because it is soft aluminum.
        I think I have some of that stuff so if I try it and it works, maybe I'll post a how-to.

        Comment

        Working...
        X